Your Office: McMurray or Select location

Production Worker

Code: 663411

Location: NC - High Point
Contact: Greensboro@mancan.com

Position Title: Craters
bi-lingual candidates are a strong plus!
QUALIFICATIONS:
1. Must have the ability to work safely in a factory environment.
2. Must have the ability to understand and follow company policies and regulatory requirements.
3. Must be able to fill out the necessary paperwork.
4. Must have good communication skills.
5. Must be able to follow verbal and written instructions.
6. Must be able to work well with others.
7. Must exhibit acceptable attendance
8. Must have the ability to be trained/certified EOJT – Level 1
9. Must have the ability to lift, stoop, bend and move quickly to perform all physical demands.
10.Must have the ability to learn our labor scanning system and scan as needed/required.

OTHER JOB SPECIFIC QUALIFICATIONS:
1. Must be able to move bales with partners into baler when doing rebales.
2. Be able to write out re-bale tickets
3. Be able to count beds to ensure bale count is correct.
4. Must be able to fill out Scrap Report as needed.

PRIMARY DUTIES:
The primary duties of the employee are (but not limited to) the following:
1. Work overtime as needed.
2. Understand company policies and regulatory requirements.
3. Conform to all Quality/Safety requirements and procedures.
4. Participate in training programs.
5. Follow all written procedures, work instructions and Inspection Plans.
6. Keep a clean and orderly work place.
7. Participate in the Continuous Improvement Process, 6S and TPM.
8. Perform other duties as assigned by your Department Supervisor.
9. Provide support in your work position for Total Productive Manufacturing’s (TPM’s) ultimate goal of maintaining our machinery in a “like new” condition with no safety concerns and no breakdowns. Key components of this process are assisting or performing quality PM’s, PDM’s and C.L.A.I.R. related task. As well as participating on Equipment Improvement Teams (EIT’s) to determine root causes of machine breakdowns.

OTHER JOB SPECIFIC PRIMARY DUTIES:
1. Count beds to ensure proper bale count
2. Bale, re-bale, and un-bale beds.
3. Move trolleys from baler out onto line if needed.
4. Report any quality machinery problems to supervisor.
5. Write rebale tickets to be turned in with baling tickets.
6. Refill paper racks at the end of shift and during shift, if necessary.
7. Operate banding gun.
8. Follow all quality specs.
Also:
a. Initiate action to prevent the occurrence of any nonconformities related to product, process and/or the system.
b. Identify and/or record any problems relating to the product, process and the management system.
c. Initiate, recommend or provide solutions through designated channels.
d. Verify the implementation of solutions.
e. Control further processing, delivery or installation of nonconforming product until the deficiency or unsatisfactory condition has been corrected.

REQUIREMENTS:
You must be able to perform these duties on or about:
30 DAYS: Be able to produce product at least at 100% productivity.
60 DAYS: Be able to produce product at least at 150% productivity.
90 DAYS: Be able to produce product at least at 175+% productivity.

Apply www.mancan.com. Click on Register, apply to 92% complete. Upload resume if one is available. Then call 336-323-7878 for the initial phone interview. You may also apply in person at Mancan Staffing located at 7360 W. Friendly Ave. Ste. 112 Greensboro, NC 27410. For the safety of our staff we require masks be worn inside our office at all times.
Mancan Staffing has the best jobs available in Greensboro NC
Using Google for jobs? Or searching Jobs Near Me?
We take applications Monday through Thursday 9am - 11am or 2pm - 4 pm and Fri 9am -11:00am only. Please bring 2 forms of government ID and resume if one was not uploaded. Temporary to permanent hire positions available. Check out all of our jobs in Greensboro NC at www.mancan.com #GreensboroMa
#JINDI

You must login or register before applying for open positions.

Back to Job Search